Husqvarna Viking Cleaning & Maintenance

In this article, we will discuss how to clean your sewing machine. We will cover the steps to take apart the machine, remove threads and bobbins, and clean the machine.

We will also provide tips on how to reassemble the machine and how often to perform maintenance and cleaning.

Key Takeaways Husqvarna Viking Cleaning

• Regular cleaning of your sewing machine is essential to keep it running smoothly.
• When cleaning your machine, be sure to remove all threads and bobbins and use a cleaning brush to remove lint and debris.
• It is recommended to perform cleaning and maintenance on your sewing machine every two to three bobbins and to take it to a professional for annual cleaning.

Removing Threads and Bobbin

Clipping Thread at Top

To start the Husqvarna Viking cleaning process, the first thing you need to do is remove the bobbin and any thread that you have in the machine. Instead of just taking the spool off and pulling, take some scissors and clip the thread at the top, and then pull the thread out of the needle.

This way, any extra lint that you have gathered up near the foot is dragged up into the machine and up into those tension disks. It’s a good habit to get into, especially if you’re using a lot of cotton threads, doing a lot of quilting, or working with linty fabrics.

Removing Bobbin Husqvarna Viking Cleaning

Next, you will need your screwdriver and cleaning brush. Start by taking the foot off, which gives you a little bit more room.

Then, also take out the needle by loosening it. If it’s been a while since you’ve changed your needle, use this time to put a new needle back in.

The bobbin case is located inside the machine, and you can lift it up to reveal the lint that has gathered in the basket area. The hook that spins around is very sharp and is what brings your thread up.

Use your cleaning brush to get in there and remove any lint that has accumulated.

It’s important to note that you should not blow into the machine or use canned air, as it can blow more lint into the back than you realize. Instead, use a dusting tool to get in and clean it all out.

After using your brush, you may still see some extra lint in the area, so make sure to clean it every three to four bobbins that you sew through. This is especially important if you are using linty fabrics or threads.

Once you have finished cleaning the bobbin area, you can reassemble the machine by putting the bobbin case back in and then the throat plate. Make sure to put your foot back on before putting the needle back in, as it helps to line up the needle correctly.

Then, test out your machine to make sure it’s good to go. Remember to do this Husqvarna Viking Cleaning process every two to three bobbins and take your machine in for an annual cleaning at your local Husqvarna Viking dealer.

Taking Apart the Machine For Husqvarna Viking Cleaning

If you’re looking to clean your machine thoroughly, it’s important to know how to take it apart. Here are the steps to follow:

Removing Foot and Needle

First, remove the foot and needle. This will give you more room to work with. Loosen the needle with a screwdriver and remove it. Then, remove the foot by pressing down on the lever and sliding it off.

Removing Throat Plate

Next, remove the throat plate. There are no screws holding it in place. Simply lift at either one of the corners and give it a little twist. It should pop off easily.

Removing Cover and Bobbin Case

Now it’s time to remove the cover and bobbin case. Lift the cover, which is a u-shape piece that sits loosely on top of the machine. Then, lift the bobbin case out of the machine.

You’ll notice that the bobbin case has two little fingers or arms. Push those in and lay the bobbin case in place.

Cleaning the machine thoroughly requires taking it apart and cleaning the different parts. By following these simple steps, you can easily remove the foot and needle, throat plate, and cover and bobbin case. This will allow you to clean the machine thoroughly and keep it running smoothly.

200 Pieces Sewing Machine Cleaning Brushes Disposable Clean Swabs Pointed Tips Cleaning Swabs Sewing Tool Multi Purpose Cleaning Swab Sticks for Paint Sewing Machine

$6.99

8 PCS Sewing Machine Cleaning Kit, Sewing Machine Brush Sewing Machine Screwdriver Repair Machine Sewing Accessories Includes Double Headed Lint Brush Tweezer Seam Rippers for Machine Sewing

$6.44

SINGER Angled Edge Lint Brush with Comfort Grip (2056)

$3.27

Cleaning the Machine

When it comes to cleaning your sewing machine, it’s important to follow a regular maintenance routine to keep it running smoothly. In this section, we’ll cover some of the key steps to cleaning your machine, including using a cleaning brush, a duster, and checking the take-up lever.

Using a Cleaning Brush

One of the best tools for cleaning your machine is a cleaning brush. This is a small brush that is designed to get into all the nooks and crannies of your machine, removing dust, lint, and other debris.

To use a cleaning brush, simply brush it over the surface of your machine, paying special attention to the areas around the needle and the bobbin.

Using a Dust It

Another great tool for cleaning your machine is a Dust it. This is a special tool that is designed to pick up dust and lint from your machine, leaving it clean and free of debris. To use a dust it, simply run it over the surface of your machine, paying special attention to the areas around the needle and the bobbin.

Checking the Take-up Lever

Finally, it’s important to check the take-up lever on your machine. This is the part of the machine that helps to pull the thread through the fabric as you sew.

If the take-up lever is dirty or clogged with lint, it can cause your machine to jam or break needles. To clean the take-up lever, simply use a cleaning brush or dust it to remove any debris that may be trapped inside.

By following these simple steps, you can keep your sewing machine running smoothly and avoid costly repairs in the future. Remember to clean your machine regularly, and to take it in for annual maintenance at your local Husqvarna Viking dealer.

With a little care and attention, your machine will provide you with years of trouble-free sewing!

Reassembling the Machine After Husqvarna Viking Cleaning

Once you have finished cleaning the machine, it’s time to reassemble it. Here are the steps to follow:

Putting Back the Bobbin Case

The first step in reassembling the machine is to put back the bobbin case. The bobbin case has two little fingers or arms.

You need to push those in and lay them in the bobbin case. The bobbin case will rock back and forth, but you can tell it’s sitting in the flat with the metal part.

Putting Back the Cover and Throat Plate

The next step is to put back the cover and throat plate. The cover is a u-shaped little guy that is loose and just sitting there.

It’s kind of a little cover that needs to be put back in place. The throat plate has no screws, so you can lift it at either one of the corners and give it a little twist. It will pop off.

To put it back, line up the nub with the back part of the machine and press firmly down on both sides until it clicks.

Putting Back the Foot and Needle

The last step is to put back the foot and needle. Start by putting the foot back on before putting the needle back in.

That way, you have a location where the needle needs to line up. Drop the needle down using your multi-purpose tool, and notice that it’s shaped like a D.

The flat side is on the back, so it keeps the needle flat side to the back.

Lower the needle down the middle of the foot, in the opening. Bring it straight up, then use your screwdriver to tighten it. Make sure you get the needle as high as it’s possible to go.

The way to know you have put it in correctly is when your needle threader lines up.

Once you have put the foot and needle back in, test out your machine to make sure it’s good to go. Remember to do this about every two to three bobbins.

It doesn’t take much for things to gather a lot of lint. Also, take it to your Husqvarna Viking dealer for its annual cleaning once a year.

Maintenance and Husqvarna Viking Cleaning Frequency

To keep your sewing machine running smoothly, it is important to perform regular maintenance and cleaning. The frequency of cleaning depends on how often you use the machine and the type of fabrics and threads you use.

Generally, it is recommended to clean your machine every two to three bobbins and to take it in for an annual cleaning by a Husqvarna Viking dealer.

Cleaning your machine regularly helps prevent lint and debris build-up, which can cause tension issues and affect the quality of your stitches. To clean your machine, start by removing the bobbin and any thread in the needle.

Use scissors to clip the thread at the top and then pull it out of the needle. This helps remove any extra lint near the foot that may have been dragged up into the machine.

Next, use a screwdriver and cleaning brush to remove the throat plate and the bobbin case. Clean these parts thoroughly, making sure to remove any lint or debris.

Be careful not to blow into the machine or use canned air, as this can blow more debris into the back of the machine.

If you notice any thread in the selective thread cutter button or near the take-up lever, use a dust-it tool to clean it out. It is important to avoid blowing into the machine or using canned air, as this can cause more problems.

Remember to replace the needle every now and then, especially if it has been a while since you last changed it. This helps ensure that your stitches are clean and even.

By following these cleaning and maintenance tips, you can keep your sewing machine running smoothly for years to come.

Source

Husqvarna

Watch the Video here